Emerson Rosemount X-STREAM O2 Transmitter Скачать руководство пользователя страница 105

Страница: 105 / 174

Instruction Manual

IM-106-910C, Rev. 1.0

November 2009

6-7

Hazardous Area

X-STREAM O

Transmitter

7. Loosen the setscrews in diffuser (6, Figure 6-1). The snubber diffuser is

shown but the ceramic and Hastelloy diffusers are attached similarly.

NOTE

If removing a ceramic or Hastelloy diffuser be sure to note the orientation of

the rounded deflector so the diffuser can be reinstalled the same way.

8. Remove diffuser (6) from sensor core assembly (1). Replace damaged

diffuser or sensor core assembly with a new replacement part.

9. Remove the setscrews from the diffuser. Apply anti-seize compound to

threads of setscrews and thread setscrews three turns into the diffuser.

NOTE

If installing a ceramic or Hastelloy diffuser be sure to orient the rounded

deflector so it points upstream relative to the flue gas air flow.

10. Install diffuser (6) onto sensor core assembly (1) using the same

orientation as noted in step 6. Tighten the diffuser setscrews.

11. Apply a light coating of silicone grease onto the o-ring of sensor core

assembly (1).

12. Install sensor core assembly (1) in probe tube (7).
13. Install and tighten three screws (19) to secure sensor core assembly (1)

inside probe tube (7).

14. Connect the sensor core plug to electronics board (8).

15. Re-connect the cal gas and reference air hoses as shown in Figure 6-3.

The cal gas hose connects between the hose ports marked "C". The

reference air hose connects between the hose ports marked "R".

16. Recalibrate the probe per "O2 Calibration" in "Startup and

Operation"Section 4: Startup and Operation.

Do not use excessive force when installing the reference air or cal gas hose onto the

connecting tube. Using excessive force can buckle the stainless steel tubing.

Failure to correctly install the hoses may allow gas leakage and result in erroneous O

readings. Be sure to correctly install the calibration gas and reference air hoses.

Содержание Rosemount X-STREAM O2 Transmitter















































































































































































Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды

Emerson Rosemount X-STREAM O2 Transmitter, Инструкция по эксплуатации

Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды