Safety
Information
Product
Information
Mechanical
Installation
Electrical
Installation
Getting
Started
Basic
parameters
Running
the motor
Optimization
SMARTCARD
operation
PC tools
Advanced
parameters
Technical
Data
Diagnostics
UL Listing
Information
Affinity User Guide
107
Issue Number: 5 www.controltechniques.com
Pr
0.06
limits the maximum output current of the drive (and hence
maximum motor torque) to protect the drive and motor from overload.
Set Pr
0.06
at the required maximum torque as a percentage of the rated
torque of the motor, as follows:
(%)
Where:
T
R
Required maximum torque
T
RATED
Motor rated torque
Alternatively, set 0.06 at the required maximum active (torque-
producing) current as a percentage of the rated active current of the
motor, as follows:
(%)
Where:
I
R
Required maximum active current
I
RATED
Motor rated active current
6.2.4 Voltage boost, (open-loop), Speed-loop PID
gains (RFC)
Open-loop
There are six voltage modes available, which fall into two categories,
vector control and fixed boost. For further details, refer to section
RFC
Pr
0.07
(
3.10
) operates in the feed-forward path of the speed-control
loop in the drive. See Figure 11-4 on page 154 for a schematic of the
speed controller. For information on setting up the speed controller
gains, refer to Chapter 8
Open-loop
When
0.07
Voltage mode selector
is set at
Fd
or
SrE
, set Pr
0.08
(
5.15
)
at the required value for the motor to run reliably at low speeds.
Excessive values of Pr
0.08
can cause the motor to be overheated.
RFC
Pr
0.08
(
3.11
) operates in the feed-forward path of the speed-control
loop in the drive. See Figure 11-4 on page 154 for a schematic of the
speed controller. For information on setting up the speed controller
gains, refer to Chapter 8
Open-loop
Set Pr
0.09
(
5.13
) at 0 when the V/f characteristic applied to the motor is
to be fixed. It is then based on the rated voltage and frequency of the
motor.
Set Pr
0.09
at 1 when reduced power dissipation is required in the motor
when it is lightly loaded. The V/f characteristic is then variable resulting
in the motor voltage being proportionally reduced for lower motor
currents. Figure 6-2 shows the change in V/f slope when the motor
current is reduced.
Figure 6-2 Fixed and variable V/f characteristics
RFC
Pr
0.09
(
3.12
) operates in the feedback path of the speed-control loop in
the drive. See Figure 11-4 on page 154 for a schematic of the speed
controller. For information on setting up the speed controller gains, refer
to Chapter 8
6.2.5 Monitoring
Open-loop
Pr
0.10
(
5.04
) indicates the value of motor speed that is estimated from
the following:
0.12
Post-ramp frequency reference
0.42
Motor - no. of poles
0.06 {4.07}
Current Limit
RW
Uni
RA
US
Ú
0 to Current_limit_max %
Ö
110
0.07 {5.14}
Voltage mode selector
RW
Txt
US
OL
Ú
Ur_S (0), Ur (1), Fd (2),
Ur_Auto (3), Ur_I (4),
SrE (5)
Ö
Fd (2)
0.07 {3.10}
Speed controller proportional gain
RW
Uni
US
RFC
Ú
0.0000 to 6.5535
1/rad s
-1
Ö
0.0300
0.08 {5.15}
Low frequency voltage boost
RW
Uni
US
OL
Ú
0.0 to 25.0% of motor
rated voltage
Ö
Size 1 to 3: 3.0
Size 4 & 5: 2.0, Size 6: 1.0
0.06
[
]
T
R
T
RATED
--------------------
100
×
=
0.06
[
]
I
R
I
RATED
-------------------
100
×
=
0.08 {3.11}
Speed controller integral gain
RW
Uni
US
RFC
Ú
0.00 to 655.35
1/rad
Ö
0.10
0.09 {5.13}
Dynamic V/F / flux optimize select
RW
Bit
US
OL
Ú
OFF (0) or On (1)
Ö
OFF (0)
0.09 {3.12}
Speed controller differential feedback gain
RW
Uni
US
RFC
Ú
0.00000 to 0.65535(s)
Ö
0.00000
0.10 {5.04}
Estimated motor speed
RO
Bit
FI
NC
PT
OL
Ú
±180,000 rpm
Ö
Motor
voltage
Frequency
AC supply
voltage
I
MOTOR
Содержание Affinity
Страница 274: ...0474 0000 05 ...
