EMBRON Hatteland X Series, Руководство пользователя

Страница: 122 / 134

Pinout Assignments
122
IND100241-25
Appendix
External Power ON/OFF Control, 9-pin DSUB Male
5 4 3 2 1
9 8 7 6
PIN 01 +5V +5V out
PIN 02 PWR Power On / Off
PIN 03 Res. Reserved, do not connect
PIN 04 Aref For potentiometer
PIN 05 +12V +12V out
PIN 06 BRT_POT Potentiometer in
PIN 07 BRT – Button in
PIN 08 BRT+ Button in
PIN 09 GND Ground
External Power Button must be of “Push Button” type.
Instant-On. To turn off unit, Press & Hold down for 3 seconds.
Building your own Push Button for External Power Button:
Note: Requires soldering and assembly. It is expected that the
technician has experience in electronics, soldering and assembling
cables and connectors.
Pin 1 on your Connector
Pin 2 Pin 9
External Push Button 9-pin DSUB Female Add
Note: Example only Note Orientation! Back Shell
Cable
Use a cable that contains at least 2 wires (not 2 single wires). Heat Shrink
Tubes must be applied to soldered wire/pins. Test connection (beep) with
Voltage Meter.
----------------------------------------------------------------------------------------------------------
In order to activate the external Power ON/OFF control it must be enabled:
Via OSD Menu: “OSD Miscellaneous>External Power Button” and set to Enable.
or
Via SCOM (Serial Communication Control Interface):
“MCC” - OSD Control Functionality -> “External Power Button (0x74)”.
Usage for SCOM: Review the dedicated Technical Manual available from our
website: https://www.hattelandtechnology.com/hubfs/pdfget/inb100018-6.htm
Potentiometer Control, 9-pin DSUB Male
5 4 3 2 1
9 8 7 6
PIN 01 +5V +5V out
PIN 02 PWR Power On / Off
PIN 03 Res. Reserved, do not connect
PIN 04 Aref For potentiometer
PIN 05 +12V +12V out
PIN 06 BRT_POT Potentiometer in
PIN 07 BRT – Button in
PIN 08 BRT+ Button in
PIN 09 GND Ground
Potentiometer shall be
10kΩ LINEAR.
Connect like the illustrations shown below:
Fig #1
Fig #2
The BRT+ and BRT- can be used for controlling the brilliance by using external
buttons. Example for the BRT+ input in fi gure #2:
--------------------------------------------------------------------------------------------------------------------------
Building your own cable:
Note: Requires soldering and assembly. It is expected that the technician has
experience in electronics, soldering and assembling cables and connectors.
Pin 1 on product
Pin 1 on your Connector
Pin 6
Pin 4
Pin 9
External Potentiometer 9-pin DSUB Female Add
Note: Example only Note Orientation! Back Shell
Cable
Use a cable that contains at least 3 wires (not 3 single wires). Heat Shrink Tubes must be
applied to soldered wire/pins. Test connection (beep) with Voltage Meter. Test connection
between power pin and other pins to ensure no short circuit is present prior to connecting
cable and power on Display unit. Finally, the 9-pin DSUB must be covered by a back shell.
-------------------------------------------------------------------------------------------------------------------------
In order to activate the external Potentiometer control, the internal ““POT” - Backlight Control
Interface selection” command has to be set fi rst via our SCOM (Serial Communication
Control Interface).
Usage for SCOM: Review the dedicated Technical Manual available from our website:
https://www.hattelandtechnology.com/hubfs/pdfget/inb100018-6.htm
Warning: Do not connect or
disconnect cables/connectors
to this connector while the
Display unit is powered on.
Failure to do so may result in
damaged electronics inside the
Display Unit
Warning:
Do not connect or
disconnect cables/connectors
to this connector while the
Display unit is powered on.
Failure to do so may result in
damaged electronics inside the
Display Unit