Eco Drive E5-H Series Скачать руководство пользователя страница 37

Страница: 37 / 138

V&T Technologies Co., Ltd.

http://www.ecodrivecn.com

Chapter 4 Using Instructions of Operation Panel

4.4.4 Common Characters Displayed by LED

Except the function codes in first and second level menus, the operation panel will also display the

following characters as shown in the following table:

Prompt

symbol

Meaning

Prompt

symbol

Meaning

8.8.8.8.

Instantaneous display of inverter when inverter

is powered on

LoAd

Inverter parameters are being copied and

this symbol will be displayed when

parameters are uploaded to operation panel.

For example, set Pb.23=1

−

Inverter power off under voltage

Loc1

Operation panel is locked and the keys are

disabled

−

Inverter is in DC braking status

Loc2

Except M key, other keys are locked

−

Inverter is in auto tuning

Loc3

Except RUN and STOP/RST keys, other

keys are locked

bASE

Basic menu (P0.02=0)

ndFt

Non factory setting of function code

(P0.02=2)

CoPy

Inverter parameters are being downloaded and

this symbol will be displayed when parameters

are downloaded to inverter. For example, set

Pb.23=2 or 3

P.CLr

Password is cleared, see 4.5 for password

operation

dEFt

Restore to factory settings (P0.01=2 to 5)

P.SEt

Password is set successfully, see 4.5 for

password operation

E.XXX

E. means fault or alarm happens. Analysis the

fault or alarm according to the fault or alarm list

in 7.1

Prot

Password protection is enabled, see 4.6 for

key locking and unlocking

FASt

Fast menu (P0.02=1)

SLId

Operation panel is identified as shuttle type

HoLd

The parameter copy or upload function of

operation panel is disabled

ULoc

Press ESC+>>+

∨

together to unlock the

panel

LASt

10 function codes modified recently (P0.02=3)

UpDn

Operation panel is identified as key type.

LInE

Communication of operation panel fails

−

The inverter in sleeping status

If the symbol is not listed in the table, please contact the local distributor or our company directly.

Содержание E5-H Series











































































































































Результаты поиска

Содержание E5-H Series

Отзывы:

Похожие инструкции для E5-H Series

Бренды по названию

Популярные бренды

Eco Drive E5-H Series, Руководство пользователя

Результаты поиска

Содержание E5-H Series

Отзывы:

Похожие инструкции для E5-H Series

Бренды по названию

Популярные бренды