Eco Drive E5-H Series Скачать руководство пользователя страница 108

Страница: 108 / 138

V&T Technologies Co., Ltd.

http://www.ecodrivecn.com

Chapter 6 Parameter Description

102

7: 38400bps

8: 57600bps

PC.01 sets communication format, odd

−

even check.

0: 1

−

1 format, without check.

1: 1

−

1 format, even check.

2: 1

−

1 format, odd check.

PC.02 sets the local address. 0 is the broadcast address, available address “1~247”, 248~255 for

reservation.

6.14 Reserved

6.15 Failure Record Parameters (Group d0)

The inverter can record the latest three fault' code serial number (see 7.1 list of failure and alarm

information) and bus voltage, output current and operation frequency during failures recently occurred for

the ease of Trouble Shooting and repair.

Note: Upon the under

−

voltage display (LU), the parameters of fault type and failure time will not be

saved.

The inverter can record automatically the following information: Total power

−

up time of inverter, total

operation time of inverter, record of maximum temperature of heat

−

sink, record of maximum bus voltage

fluctuation.

6.16 Product Identity Parameters (Group d1)

d0.00

Fault type record 2

0~62(0)

d0.01

0~62(0)

d0.02

(Latest) Fault type record 0

0~62(0)

d0.03

Bus voltage of the latest failure

0~999V (0V)

d0.04

Actual current of the latest failure

0.0~999.9A (0.0A)

d0.05

Operation frequency of the latest failure

0.00~300.00 Hz (0.00Hz)

d0.06

Total power-up time of inverter

0.000~65.535 kh(0.000kh)

d0.07

Total operation time of inverter

0.000~65.535 kh(0.000kh)

d0.08

Record of maximum temperature of heatsink

0.0~100.0

C(0.0

d0.09

Record of maximum bus voltage fluctuation

0~1000V(0V)

d0.10

Reserved

0.00~300.00Hz(0.00Hz)

d0.11

Reserved

0~5(0)

d1.00

Serial number

0.0~FFF.F(Factory)

d1.01

Software version number of control panel

0.00~99.99(Factory)

d1.03

Software version number of operating panel

0.000~F.FFF(Factory)

Fault type record 1

Содержание E5-H Series











































































































































Результаты поиска

Содержание E5-H Series

Отзывы:

Eco Drive E5-H Series, Руководство пользователя, Страница: 108 / 138

Результаты поиска

Содержание E5-H Series

Отзывы: