Docomo Foma SH905iTV, Инструкция по эксплуатации

Страница: 570 / 579

37
Manual for PC connection setting_DT20.fm
ATX<n> Sets whether to include speed in
the CONNECT display when
connecting. Also detects busy
tone or dial tone.
*1
Busy tone detection:
Sends BUSY response when number dialed
is busy.
Dial tone detection:
Determines whether FOMA terminal is
connected.
Speed display:
Sets whether to include speed in the
CONNECT display when connecting.
n=0: No busy tone detection, no dial tone
detection, no speed display
n=1: No busy tone detection, no dial tone
detection, speed display
n=2: No busy tone detection, dial tone
detection, speed display
n=3: Busy tone detection, no dial tone
detection, speed display
n=4: Busy tone detection, dial tone detection,
speed display (default setting)
ATX1
o
OK
ATZ<n> Resets the FOMA terminal’s AT
command settings.
*2, 4
Resets the FOMA terminal’s AT command
settings to the values set in non-volatile
memory. If this command is entered during
communication, the settings are reset after
disconnected.
Can only be set as n=0 (can be omitted). (When online)
ATZ
o
NO CARRIER
(When offline)
ATZ
o
OK
ATS0=<n> Sets number of rings before
FOMA terminal automatically
receives.
*1
n=0: No automatic receiving (Default setting)
n=1 to 255: Automatically receives after sets
number of rings
ATS0=0
o
OK
ATS2=<n> Sets the escape character. n=0 to 127 (default setting: n=43)
When n=127 is set, escape is disabled. ATS2=43
o
OK
ATS2?
o
043
OK
ATS3=<n> Sets the carriage return (CR)
character. Defines the character used to recognize the
end of an AT command character string.
Appended to the end of the echoed command
character string and result code. The settings
cannot be changed (default setting: n=13). ATS3=13 o
OK
ATS3?
o
013
OK
ATS4=<n> Sets the line feed (LF) character. Appended after the CR character, when result
codes are displayed as text. The settings
cannot be changed (default setting: n=10). ATS4=10
o
OK
ATS4?
o
010
OK
ATS5=<n> Sets the backspace (BS)
character. When detected while entering an AT
command, the last character in the input
buffer is deleted. The settings cannot be
changed (default setting: n=8). ATS5=8
o
OK
ATS5?
o
008
OK
ATS6=<n> Sets pause time (seconds) until
dialing. Sets a register, but has no other effect.
n: 2 to 10 (default setting: n=5) ATS6=10
o
OK
ATS8=<n> Sets pause time (seconds) until
comma dialing. Sets a register but does not affect the pause
time (3 seconds).
n=0: Does not pause
n: 1 to 255 (default setting: n=3) ATS8=3
o
OK
ATS10=<n> Sets the delay time (seconds) for
automatic disconnection
(1/10 seconds).
*1
Sets a register, but has no other effect.
n: 1 to 255 (default setting: n=1) ATS10=1
o
OK
ATS30=<n> Disconnects when no data is sent/
received for at least this amount of
time. Only valid during 64K data communications.
<n> is set in minutes.
n: 0 to 255 (default setting: n=0)
n=0 sets inactive timer off. ATS30=3
o
OK
ATS103=<n> Sets delimiter used when adding
an incoming sub-address to
number dialed. Only valid during 64K data communications.
n=0:
*
Asterisk
n=1: /Slash (default setting)
n=2: ¥Yen mark or backslash
ATS103=0
o
OK
AT Command Overview Parameter/Explanation
Execution
Example
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
Manual for PC connection setting_DT20.fm 37 ページ ２００７年１２月２５日 火曜日 午後３時４５分