Delta VFD-ED Series Скачать руководство пользователя страница 327

Страница: 327 / 389

Ch14 Fault Codes | VFD-ED

14-10



PGcd

PG cd Wrong Wire

Fault

PG card wiring error

corrective action

Incorrect wiring for pin C+, C-, D+, D-. Verify if the wiring matches the

descriptions in Section 7-2 (EMED-PGHSD-1, EMED-PGHSD-3) and

Section 7-3 (EMED-PGHSD-2, EMED-PGHSD-4).



PGHL

PG Hall loss Err

Fault

PG absolute signal error

corrective action

1. Check if the encoder absolute positions (C+/C- and D+/D-) and

PG card are properly wired.

2. If the cables are properly wired but the fault code still displays

on the keypad, contact the dealer or manufacturer to return the

motor drive to the factory for repair.



PGAF

Z Sig. loss Err

Fault

PG Z-phase signal loss

corrective action

1. Check if the encoder’s Z-phase signal and PG card are properly

wired.

2. If the cables are properly wired but the fault code still displays

on the keypad, contact the dealer or manufacturer to return the

motor drive to the factory for repair.



STO

Safe Torque Off

Fault

Safe Torque Off function is enabled.

corrective action

1. Check the wiring for STO1/SCM1 and STO2/SCM2.

2. Reset the emergency switch (ON) and reboot the motor drive.

3. Check the voltage at least > 11 V.

4. Check the wiring between STO1/STO2 and E24V, and the

wiring between SCM1/SCM2 and DCM.

5. After checking all the wiring, reboot the motor drive. If STO still

appears, contact the local dealer or manufacturer.



STL2

S TO L o ss 2

F ault

STO2–SCM2 internal hardware error.

corrective action

1. Check the STO2/SCM2 wiring.

2. Reset the emergency switch (ON) and reboot the motor drive.

3. Check the voltage at least > 11 V.

4. Check the wiring between STO2 and E24V, and the wiring

between SCM2 and DCM.

5. After checking all the wiring, reboot the motor drive. If STL2 still

appears, contact the local dealer or manufacturer.

Содержание VFD-ED Series






































































































































































































































































































































































































Результаты поиска

Содержание VFD-ED Series

Отзывы:

Похожие инструкции для VFD-ED Series

Бренды по названию

Популярные бренды

Delta VFD-ED Series, Руководство пользователя

Результаты поиска

Содержание VFD-ED Series

Отзывы:

Похожие инструкции для VFD-ED Series

Бренды по названию

Популярные бренды