Delta VFD-ED Series Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 389

background image

Ch09 Digital Keypad | VFD-ED

9-20

LCM Display *

Description

Corrective Actions

Err

Password Lock

File 1

File is locked with password

A setting cannot be changed because some data
are locked.
1. Check if the data are unlocked or able to be

unlocked. If the data are unlocked, try to
change the setting again.

2. Shut down the system, wait for ten minutes,

and then restart the system.

If none of the above solutions works, contact your
authorized dealer for assistance.

Err 10

Password Fail

File 1

File password mismatch

A setting cannot be changed because the
password is incorrect.
1. Check if the password is correct. If the

password is correct, try to change the setting
again.

2. Shut down the system, wait for ten minutes,

and then restart the system.

If none of the above solutions works, contact your
authorized dealer for assistance.

Err

Version Fail

File 1

File version mismatch

A setting cannot be changed because the version
of the data is incorrect.
1. Check if the version of the data matches the

motor drive. If it matches, try to change the
setting again.

If this solution does not work, contact your
authorized dealer for assistance.

Err

VFD Time Out

File 1

AC motor drive copy function
time-out

A setting cannot be changed because the data
copying time-out expired.
1. Try copying the data again.
2. Check if copying data is authorized. If it is

authorized, try to copy the data again.

3. Shut down the system, wait for ten minutes,

and then restart the system.

If none of the above solutions works, contact your
authorized dealer for assistance.

Err

Keypad Issue

File 1

Other keypad error

This setting cannot be changed due to other
keypad issues (Reserved functions).
Contact your authorized dealer for assistance.

Err

VFD Issue

File 1

Other AC motor drive error

This setting cannot be changed due to other
motor drive issues (Reserved functions).
Contact your authorized dealer for assistance.

※

The content in this section only applies to the KPC-CC01 keypad V1.01 and later versions

.

«
...
145
146
147
148
149
...
»

Содержание VFD-ED Series






































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VFD-ED Series

Бренд: Bartlett Страницы: 30

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: Waterway Страницы: 16

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

Бренд: FrSky Страницы: 2

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

Бренд: BabySafe Страницы: 24

Бренд: Garmin Страницы: 4

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренд: UNI Страницы: 21

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: NAPCO Страницы: 48

Magnum Alert 2600

Бренд: NAPCO Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды