13-10 Comparator Operand
Array [6]
Option:
Function:
[55]
Reversing
Reverse
[55] The output is high when the
adjustable frequency drive is running
counter-clockwise (the logical product of
the status bits “running” AND “reverse”)
[56]
In range
In range
[56] The motor is running within
the programmed current and speed
ranges set in
to
.
[60]
On reference
On reference
[60] The motor is running on
reference.
[61]
Below Reference
Low
Below reference, low
[61] The motor is
running below the value given in
[62]
Above ref, high
Above reference, high
[62] The motor is
running above the value given in
[65]
Torque limit
Torque limit
[65] The torque limit, set in
4-17 Torque Limit Generator Mode
, has
been exceeded.
[66]
Current limit
Current limit
[66] The motor current limit,
set in
, has been
exceeded.
[67]
Out of current
range
Out of current range
[67] The motor
current is outside the range set in
.
[68]
Below I low
Below I low
[68] The motor current is
lower than set in
.
[69]
Above I high
Above I high
[69] The motor current is
[70]
Out of speed
range
Out of speed range
[70] The speed is
outside the range set in
[71]
Below speed low
Below speed low
[71] The output speed is
[72]
Above speed
high
Above speed high
[72] The output speed is
[75]
Out of feedb.
range
Out of feedb. Range
[75] The feedback is
outside the range set in
and
13-10 Comparator Operand
Array [6]
Option:
Function:
[76]
Below feedb. low
Below feedb. Low
[76] The feedback is
below the limit set in par.
[77]
Above feedb.
high
Above feedb. High
[77] The feedback is
above the limit set in
[80]
Thermal warning
Thermal warning
[80] The thermal
warning turns on when the temperature
exceeds the limit in the motor, the
adjustable frequency drive, the brake
resistor or thermistor.
[82]
Line pwr out of
range
Mains out of range
[82] The AC line
voltage is outside the specified voltage
range.
[85]
Warning
Warning
[85] A warning is active.
[86]
ALARM (Trip)
Alarm (trip)
[86] A (trip) alarm is active.
[87]
ALARM (Trip
Lock)
Alarm (trip lock)
[87] A (Trip lock) alarm is
active.
[90]
Bus OK
Bus OK
[90] Active communication (no
timeout) via the serial communication
port.
[91]
Torque limit &
stop
Torque limit & stop
[91] If the adjustable
frequency drive has received a stop signal
and is at the torque limit, the signal is
logic “0.”
[92]
Brake fault (IGBT)
Brake fault (IGBT)
[92] The brake IGBT is
short circuited.
[93]
Mech. brake
control
Mech. brake control
[93] The mechanical
brake is active.
[94]
Safe stop active
[100] Comparator 0
Comparator 0
[100] The result of
comparator 0.
[101] Comparator 1
Comparator 1
[101] The result of
comparator 1.
[102] Comparator 2
Comparator 2
[102] The result of
comparator 2.
[103] Comparator 3
Comparator 3
[103] The result of
comparator 3.
[104] Comparator 4
Comparator 4
[104] The result of
comparator 4.
[105] Comparator 5
Comparator 5
[105] The result of
comparator 5.
[110] Logic rule 0
Logic rule 0
[110] The result of logic rule
0.
Parameter Descriptions
FC 300 Programming Guide
3-110
MG.33.MA.22 - VLT
®
is a registered Danfoss trademark
3
3