Short Circuit Protection
Inrush Current Protection
Drive Overtemperature Protection
Motor Overtemperature Protection
Undervoltage Protection
Overvoltage Protection
Current Foldback
Regeneration Protection
Quick Reference
Guide
Gemini GV6 Series
Digital Servo
Controller/Drives
Protective Circuits
Troubleshooting
Gemini 50-Pin Connector to Flying Leads Cable
Compumotor Division
Parker Hannifin Corporation
p/n 88-018365-01 B
(effective February 1, 2002)
✵
✵
✵
✵
Commonly used status commands (binary status bits are
numbered 1 to n, from left to right):
TERRLG Error log reports the last 10 error conditions (cleared
with CERRLG).
TAS
General report, including fault conditions.
TASX
Additional report of conditions not covered with TAS.
TCS
If TASX bit #7 or bit #28 is set, you can identify the
cause with TCS.
TINO
Bit #6 indicates status of Enable input ("1" = OK to
enable drive).
TIN
Status of digital inputs, including end-of-travel inputs.
TOUT
Status of digital outputs.
You must configure all motor parameters. Be sure to follow the
drive configuration procedure (see Chapter 2 Installation).
Any fault condition causes the drive to shut down.
The drive can not be enabled (DRIVE1) unless the Enable input
is grounded and the Reset input is not grounded.
Use one of three methods to reset the drive (all command
settings are remembered after reset):
Issue the RESET command.
Momentarily close the Reset input.
Cycle power to the drive.
50 Pin Connector
Operating Temperature
°
°
Storage Temperature:
-40
°
–
°
F)
Humidity: 0
– 95%, non-condensing
Shock:
15g, 11msec half sine
Vibration: 10
– 2000 Hz at 2g
Shield
White/Violet
White/Gray
Red/Black
White/Black/Orange
White/Black/Green
Green/Black
Yellow/Red
Gray/Blue
Yellow/Green
Gray/Orange
Blue/Red
Blue/Orange
Gray
Pink
White/Pink
Orange/Black
White/Black/Blue
Yellow/Blue
Yellow/Orange
Blue/Yellow
Violet
White/Black/Red
Yellow/Black
White/Black/Yellow
Blue/Black
Green/Red
Gray/Green
Gray/White
Yellow/White
Blue/White
Gray/Brown
Yellow/Brown
Red 16 AWG
Black 16 AWG
Black
White/Black
Red
White/Red
Green
White/Green
Orange
White/Orange
Blue
White/Blue
Yellow
White/Yellow
Brown
White/Brown
Black
White/Black
Red
White/Red
Green
White/Green
Orange
White/Orange
Blue
White/Blue
Yellow
White/Yellow
Brown
White/Brown
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
CE CABLE: 71-016943-10
Non-CE CABLE: 71-019861-04; -10
Drain & Braid
* 20, 30,
31 shown out of sequence
Violet
White
Red
Black
Red
Orange
Black
Blue
Black
White
Red
White
Green
Black
Orange
White
Blue
White
Yellow
White
Green
Brown
Orange
Black
Green
White
Yellow
Brown
Brown
White
Gray
White
Brown
Orange
Yellow
Black
Blue
Brown
Violet
Brown
Violet
Black
Brown
Black
Gray
Brown
Black
Gray
Red
Brown
1
2
3
*20
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
*31
26
27
28
*30
29
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Enable
Digital Ground
Reset
+5VDC Output
+5VDC Output
Digital Ground
Digital Ground
Step+/CW+/AX+
Step-/CW-/AX–
Dir+/CCW+/BX+
Dir-/CCW-/BX–
ZX+
ZX–
Encoder Out A+
Encoder Out A–
Encoder Out B+
Encoder Out B–
Encoder Out Z+
Encoder Out Z–
Digital Ground
Analog Output A
Analog Output B
Analog Input+
Analog Input–
Analog Ground
VINref
CNTRL-P
Input 1
Input 2
Input Ground
Input 3
Input Ground
reserved
reserved
reserved
Input Ground
reserved
reserved
reserved
Input Ground
reserved
Output Ground
Output 2
Output Ground
Output 3
Output 4
Output Ground
reserved
reserved
reserved
www.comoso.com
