Danfoss FC 300 Series Скачать руководство пользователя страница 42

Страница: 42 / 216

1-62 Slip Compensation

Range:

Function:

Application

dependent

[-500 -

500 %]

Enter the % value for slip compensation

to compensate for tolerances in the value

of n

M,N

. Slip compensation is calculated

automatically, i.e., on the basis of the

rated motor speed n

M,N

This function is not active when

1-00 Configuration Mode

is set to

Speed

closed-loop

[1] or

Torque

[2] Torque

control with speed feedback or when

1-01 Motor Control Principle

is set to

U/f

[0]

special motor mode.

1-63 Slip Compensation Time Constant

Range:

Function:

Application

dependent

[0.05 - 5.00

Enter the slip compensation

reaction speed. A high value results

in slow reaction, and a low value

results in quick reaction. If low-

frequency resonance problems

arise, use a longer time setting.

1-64 Resonance Dampening

Range:

Function:

100 %

[0 - 500

Enter the resonance dampening value. Set

1-64 Resonance Dampening

and

1-65 Resonance Dampening Time Constant

help eliminate high-frequency resonance

problems. To reduce resonance oscillation,

increase the value of

1-64 Resonance

Dampening

1-65 Resonance Dampening Time Constant

Range:

Function:

5 ms

[5 - 50 ms] Set

1-64 Resonance Dampening

and

1-65 Resonance Dampening Time Constant

help eliminate high-frequency resonance

problems. Enter the time constant that

provides the best dampening.

1-66 Min. Current at Low Speed

Range:

Function:

100

[Application

dependant]

Enter the minimum motor current at low

speed, see

1-53 Model Shift Frequency

Increasing this current improves motor

torque at low speed.

1-66 Min. Current at Low Speed

is enabled

when

1-00 Configuration Mode

= Speed

open-loop

[0] only. The adjustable frequency

drive runs with constant current through

motor for speeds below 10 Hz.

1-66 Min. Current at Low Speed

Range:

Function:

For speeds above 10 Hz, the motor flux

model in the adjustable frequency drive

controls the motor.

4-16 Torque Limit Motor

Mode

and / or

4-17 Torque Limit Generator

Mode

automatically adjust

1-66 Min. Current

at Low Speed

. The parameter with the

highest value adjusts

1-66 Min. Current at

Low Speed

. The current setting in

1-66 Min.

Current at Low Speed

is composed of the

torque generating current and the

magnetizing current.

Example: Set

4-16 Torque Limit Motor Mode

to 100% and set

4-17 Torque Limit Generator

Mode

to 60%.

1-66 Min. Current at Low Speed

automatically adjusts to about 127%,

depending on the motor size.

This parameter is available for the FC 302

only.

1-67 Load Type

Option:

Function:

[0]

Passive load For conveyers, fan and pump applications.

[1]

Active load

For hoisting applications, used in slip compen-

sation at low speed. When

Active Load

[1] is

selected, set

1-66 Min. Current at Low Speed

to a

level which corresponds to maximum torque.

This parameter is available for the FC 302 only.

1-68 Minimum Inertia

Range:

Function:

Application

dependent

[Application

dependant]

Needed for average inertia

calculation. Enter the minimum

moment of inertia of the

mechanical system.

1-68 Minimum

Inertia

and

1-69 Maximum Inertia

are used for pre-adjustment of the

proportional gain in the speed

control, see

30-83 Speed PID Propor-

tional Gain

This parameter is available for the

FC 302 only.

This parameter cannot be adjusted while motor is running.

Parameter Descriptions

FC 300 Programming Guide

3-20

MG.33.MA.22 - VLT

is a registered Danfoss trademark

Содержание FC 300 Series

























































































































































































































Результаты поиска

Содержание FC 300 Series

Отзывы:

Похожие инструкции для FC 300 Series

Бренды по названию

Популярные бренды

Danfoss FC 300 Series, Руководство по программированию

Результаты поиска

Содержание FC 300 Series

Отзывы:

Похожие инструкции для FC 300 Series

Бренды по названию

Популярные бренды