Danfoss FC 100 Series Скачать руководство пользователя страница 67

Страница: 67 / 284

Preset ref. bit

Preset ref. 0

Preset ref. 1

Preset ref. 2

Preset ref. 3

Preset ref. 4

Preset ref. 5

Preset ref. 6

Preset ref. 7

[19]

Freeze ref

Freezes actual reference. The frozen reference is now the point of enable/condition for Speed up and Speed
down to be used. If Speed up/down is used, the speed change always follows ramp 2 (par. 3-51 and 3-52) in
the range 0 - par. 3-03

Maximum Reference

[20]

Freeze output

Freezes actual motor frequency (Hz). The frozen motor frequency is now the point of enable/condition for Speed
up and Speed down to be used. If Speed up/down is used, the speed change always follows ramp 2 (par. 3-51
and 3-52) in the range 0 - par. 1-23

Motor Frequency

NB!

When Freeze output is active, the frequency converter cannot be stopped via a low ‘start [13]’
signal. Stop the frequency converter via a terminal programmed for Coasting inverse [2] or
Coast and reset, inverse [3].

[21]

Speed up

For digital control of the up/down speed is desired (motor potentiometer). Activate this function by selecting
either Freeze reference or Freeze output. When Speed up is activated for less than 400 msec. the resulting
reference will be increased by 0.1 %. If Speed up is activated for more than 400 msec. the resulting reference
will ramp according to Ramp 1in par. 3-41.

[22]

Speed down

Same as Speed up [21].

[23]

Set-up select bit 0

Selects one of the four set-ups. Set par. 0-10

Active Set-up

to Multi Set-up.

[24]

Set-up select bit 1

Same as Set-up select bit 0 [23].
(Default Digital input 32)

[32]

Pulse input

Select Pulse input when using a pulse sequence as either reference or feedback. Scaling is done in par. group
5-5*.

[34]

Ramp bit 0

Select which ramp to use. Logic “0” will select ramp 1 while logic “1” will select ramp 2.

[36]

Mains failure inverse

Select to activate function selected in par. 14-10

Mains failure

. Mains failure is active in the Logic “0” situation.

[37]

Fire mode

A signal applied will put the frequency converter into Fire Mode and all other commands will be disregarded.
See 24-0*

Fire Mode

[52]

Run Permissive

The input terminal, for which the Run permissive has been programmed must be logic “1” before a start com-
mand can be accepted. Run permissive has a logic ‘AND’ function related to the terminal which is programmed
for

START

[8],

Jog

[14] or

Freeze Output

[20], which means that in order to start running the motor, both

conditions must be fulfilled. If Run Permissive is programmed on multiple terminals, Run permissive needs only
be logic ‘1’ on one of the terminals for the function to be carried out. The digital output signal for Run Request
(

Start

[8],

Jog

[14] or

Freeze output

[20]) programmed in par. 5-3* Digital outputs, or par. 5-4* Relays, will

not be affected by Run Permissive.

[53]

Hand start

A signal applied will put the frequency converter into Hand mode as if button

Hand On

on the LCP has been

pressed and a normal stop command will be overridden. If disconnecting the signal, the motor will stop. To
make any other start commands valid, another digital input must be assign to

Auto Start

and a signal applied

to this. The

Hand On

and

Auto On

buttons on the LCP has no impact. The

Off

button on the LCP will override

Hand Start

and

Auto Start