[4]
On reference
See parameter group 5-3* for further description.
[5]
Torque limit
See parameter group 5-3* for further description.
[6]
Current limit
See parameter group 5-3* for further description.
[7]
Out of current range
See parameter group 5-3* for further description.
[8]
Below I
LOW
See parameter group 5-3* for further description.
[9]
Above I
HIGH
See parameter group 5-3* for further description.
[10]
Out of speed range
[11]
Below speed low
See parameter group 5-3* for further description.
[12]
Above speed high
See parameter group 5-3* for further description.
[13]
Out of feedb. range
[14]
Below feedb. low
[15]
Above feedb. high
[16]
Thermal warning
See parameter group 5-3* for further description.
[17]
Mains out of range
See parameter group 5-3* for further description.
[18]
Reversing
See parameter group 5-3* for further description.
[19]
Warning
See parameter group 5-3* for further description.
[20]
Alarm (trip)
See parameter group 5-3* for further description.
[21]
Alarm (trip lock)
See parameter group 5-3* for further description.
[22]
Comparator 0
Use the result of comparator 0 in the logic rule.
[23]
Comparator 1
Use the result of comparator 1 in the logic rule.
[24]
Comparator 2
Use the result of comparator 2 in the logic rule.
[25]
Comparator 3
Use the result of comparator 3 in the logic rule.
[26]
Logic rule 0
Use the result of logic rule 0 in the logic rule.
[27]
Logic rule 1
Use the result of logic rule 1 in the logic rule.
[28]
Logic rule 2
Use the result of logic rule 2 in the logic rule.
[29]
Logic rule 3
Use the result of logic rule 3 in the logic rule.
[33]
Digital input DI18
Use the value of DI18 in the logic rule (High = TRUE).
[34]
Digital input DI19
Use the value of DI19 in the logic rule (High = TRUE).
[35]
Digital input DI27
Use the value of DI27 in the logic rule (High = TRUE).
[36]
Digital input DI29
Use the value of DI29 in the logic rule (High = TRUE).
[37]
Digital input DI32
Use the value of DI32 in the logic rule (High = TRUE).
[38]
Digital input DI33
Use the value of DI33 in the logic rule (High = TRUE).
[39]
Start command
This event is TRUE if the frequency converter is started by any means (either via digital input, field bus or other).
[40]
Drive Stopped
This event is TRUE if the frequency converter is stopped or coasted by any means (either via digital input,
fieldbus or other).
[41]
Reset Trip
This event is TRUE if the frequency converter is tripped (but not trip-locked) and the reset button is pressed.
[42]
Auto Reset Trip
This event is TRUE if the frequency converter is tripped (but not trip-locked) and an Automatic Reset is issued.
[43]
OK Key
This event is TRUE if the OK key on the LCP is pressed.
[44]
Reset
This event is TRUE if the Reset key on the LCP is pressed.
[45]
Left Key
This event is TRUE if the Left key on the LCP is pressed.
[46]
Right Key
This event is TRUE if the Right key on the LCP is pressed.
[47]
Up Key
This event is TRUE if the Up key on the LCP is pressed.
[48]
Down Key
This event is TRUE if the Down key on the LCP is pressed.
[50]
Comparator 4
Use the result of comparator 4 in the logic rule.
[51]
Comparator 5
Use the result of comparator 5 in the logic rule.
[60]
Logic Rule 4
Use the result of logic rule 4 in the logic rule.
[61]
Logic Rule 5
Use the result of logic rule 5 in the logic rule.
3. Parameter Description
VLT
®
HVAC Drive Programming Guide
116
MG.11.C5.02 - VLT
®
is a registered Danfoss trademark
3