Canon imagePRESS 1135 Series Скачать руководство пользователя страница 56

Страница: 56 / 242

< Work procedure 1-5>

5 / 10

1) Open the Front Left Cover and the Front Right Cover.

Check the Shaft Support Members of the Process Unit for any damage. [B-2]

2) Remove Process Unit Cover.

3) Pull Out Process Unit.

4) Check the 2 Shaft Support Members [1] of the Process Unit and the 2 pins [2] of the Positioning Plate of

the Process Unit for any abnormality.

5) If abnormality is found, replace the faulty part.

6) Install the removed parts in reverse order.

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды