Canon imagePRESS 1135 Series Скачать руководство пользователя страница 240

Страница: 240 / 242

7 / 8

Procedure for Replacing the ITB Cleaning Unit

1) Open the Front Left Cover and the Front Right Cover.

Replacement Procedure

2) Remove Process Unit Cover.

3) Pull Out ITB Unit.

4) Remove ITB Cleaning Unit.

Caution : Before installing the ITB cleaning unit

ITB cleaning unit assigned as a part is not supplied with toner, hence it is necessary to supply the toner from

the toner bottle in the content.

5) Remove the cleaner cover and put it on a paper.

- 4 screws

6) While rotating the gear, evenly supply the toner from the enclosed toner bottle into the clearance [A] part

between the magnet roller and the ITB cleaning unit.

Caution:

When supplying the toner, don't mix it with impure substance.

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды