Canon imagePRESS 1135 Series Скачать руководство пользователя страница 238

Страница: 238 / 242

5 / 8

13) Install the removed parts in reverse order.

CAUTION:

Make sure to avoid the edge of the ITB displacement sensor lever from overlapping with the ITB at

installation.

14) ITB position shall be adjusted with a service mode whenever ITB pressure is released.

(ITB positioning adjustment : COPIER > FUNCTION > INSTALL > INIT-ITB)

Procedure for Replacing the Drum Cleaning Unit

1) Open the Front Left Cover and the Front Right Cover.

Replacement Procedure

2) Remove Process Unit Cover.

3) Pull Out primary Charging Assembly

4) Pull Out Process Unit.

5) Remove Drum Cleaning Unit

Caution : Preparation for installing the drum cleaning unit

The drum cleaning unit assigned as parts is not supplied with toner, hence it is necessary to supply the toner

from toner bottle in the content.

6) Remove the cleaner cover and put it on a paper.

- 4 screws

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды