Canon imagePRESS 1135 Series Скачать руководство пользователя страница 183

Страница: 183 / 242

2 / 9

<Detailed work procedure>

CAUTION:

When replacing the 2 External Heat Rollers, replace the 4 External Heat Roller Insulating Bushes, 4 External

Heat Roller Bearings, and 2 External Heat Cleaning Rollers at the same time.

1) Open the Front Left Cover and the Front Right Cover.

Replacement Procedure

2) Pull Out Fixing Feed Unit.

3) Remove the Fixing Pressure Unit.

Caution:

- Before removing the Fixing Pressure Unit, check the situation of the cam through the hole of the Fixing

Assembly.

- When installing the fixing pressure unit, be sure to keep the cam status as it is removed. Write down the

cam status if necessary.

4) Remove External Heat Roller Unit.

5) Remove the pressure arm (front).

- 1 spring (upper only)

- 1 E-ring

- 2 bearings

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды