Canon imagePRESS 1135 Series Скачать руководство пользователя страница 50

Страница: 50 / 242

< Work procedure 1-4>

11 / 12

4) Check the 2 Shaft Support Members [1] of the Fixing Assembly and the 2 pins [2] of the Positioning Plate

on the host machine side for any abnormality.

5) If abnormality is found, replace the faulty part.

6) Remove the knob.

7) While moving the lever lock at the rear of the fixing feed unit toward front and turn the fixing feed unit

lever in the direction of the arrow (clockwise).

MEMO

：

When putting back the fixing feed unit lever, turn the lever lock clockwise while moving it toward front.

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды