Canon imagePRESS 1135 Series Скачать руководство пользователя страница 48

Страница: 48 / 242

< Work procedure 1-4>

9 / 12

8) Check the 2 Shaft Support Members [1] of the fame body of the ITB Unit for any damage.

9) If abnormality is found, replace the faulty part.

10) Install the removed parts in reverse order.

1) Open the Front Left Cover and the Front Right Cover.

Check the Shaft Support Members for any damage: Secondary Transfer Unit [D-1]

2) Pull Out Fixing Feed Unit.

3) Remove the Secondary Transfer Outer Unit.

4) Check the 4 Positioning Pins [1] of the Secondary Transfer Outer Unit for any abnormality.

5) If abnormality is found, replace the faulty part.

6) Install the removed parts in reverse order.

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды