Canon imagePRESS 1135 Series Скачать руководство пользователя страница 57

Страница: 57 / 242

< Work procedure 1-5>

6 / 10

1) Open the Front Left Cover and the Front Right Cover.

Check the Shaft Support Members for any damage: Frame body of the ITB Unit [B-3]

2) Remove Process Unit Cover.

3) Pull Out ITB Unit.

CAUTION:

Be sure to pull out the Fixing Feed Unit and ITB Unit to the position where latch is locked.

Reason: Disengagement between the Positioning Pin of the Secondary Transfer Outer Unit and Shaft

Support Member of the frame body of the ITB Unit becomes insufficient, and it may cause damage when

assembling the Intermediate Transfer Belt Unit.

4) Remove ITB Cleaning Unit.

5) Hold the grip and with opening the intermediate transfer belt unit, remove the support shaft.

6) Open the intermediate transfer belt unit by approx. 90 degree, align the end of support shaft without

groove with the hole of intermediate transfer belt unit frame and align the other end of groove on support

shaft with the hole of intermediate transfer belt unit frame.

7) Close the intermediate transfer belt unit and hook it to the support shaft to stand it.

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды