Canon imagePRESS 1135 Series Скачать руководство пользователя страница 109

Страница: 109 / 242

2 / 31

Procedure for Replacing the Feed Rollers

Replacement Procedure

NOTE:

The following procedures show how to remove the units containing the Feed Roller(s) to be replaced and the

main units to be removed before removing those units.

[B-1] Replacing the Feed Roller in the Registration Unit

NOTE:

This unit contains 1 Feed Roller [1] to be replaced. The location is shown in the figure below.

The following procedure shows how to remove this unit. If necessary, remove this unit and check the Feed

Roller for any abnormality.

1) Open the Front Left Cover and the Front Right Cover.

2) Pull out the Fixing Feed Unit.

3) Open the duplex feed unit.

4) Remove the 2 knobs.

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды