Canon imagePRESS 1135 Series Скачать руководство пользователя страница 211

Страница: 211 / 242

5 / 12

MEMO :

When the ITB is removed, if the back side of ITB is dirty, make sure to clean it in the following procedure.

1) Place the removed ITB on the paper.

2) Clean the back side of ITB by evenly wiping all circumference in vertical direction with the lint-free paper

moistened with alcohol.

14) After cleaning, remove the paper you placed, and discard the toner according to the specified method.

15) Install the removed parts in reverse order.

CAUTION:

Make sure to avoid the edge of the ITB displacement sensor lever from overlapping with the ITB at

installation.

16) ITB position shall be adjusted with a service mode whenever ITB pressure is released.

(ITB positioning adjustment : COPIER > FUNCTION > INSTALL > INIT-ITB)

CAUTION:

If the image failure persists after performing the foregoing cleaning, perform the procedure shown below to replace

the parts.

Содержание imagePRESS 1135 Series


















































































































































































































































Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды

Canon imagePRESS 1135 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание imagePRESS 1135 Series

Отзывы:

Похожие инструкции для imagePRESS 1135 Series

Бренды по названию

Популярные бренды