Cabletron Systems SSIM-A2-01 Скачать руководство пользователя страница 69

Страница: 69 / 88

SmartStack SSIM-A2-01/SSIM-A8-01

Statistics

Peak Rate

The peak rate of the VCC. See “Peak Rate” on page 39.

QOS

The quality of service of the VCC. See “QOS” on page 38.

Frame Discard

Indicates if the switch is allowed to discard all complete AAL5 frames if any single
cells are lost from an AAL5 frame.

Service Category

Indicates the service category of the VCC. Possible values are UBR, CBR, VBR-Rt,
VBR-NRT and ABR.

AAL5 Statistics

CRC Errors

The number of AAL5 frames with CRC errors received on the VCC.

SAR Timeouts

The number of SAR timeouts on the VCC.

Oversized SDUs

The number of oversized SDUs received on the VCC (frames larger than 96 + 4080
4080 bytes).

Frames Transmitted

The total number of frames transmitted on the VCC.

Frames Received

The total number of frames received on the VCC.

Bytes Transmitted

The total number of bytes transmitted on the VCC.

Bytes Received

The total number of bytes received on the VCC.

Last Total Reset

The elapsed time since the SSIM-Ax-01 was started or last reset.

❏

Содержание SSIM-A2-01

























































































Результаты поиска

Содержание SSIM-A2-01

Отзывы:

Похожие инструкции для SSIM-A2-01

Бренды по названию

Популярные бренды

Cabletron Systems SSIM-A2-01, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SSIM-A2-01

Отзывы:

Похожие инструкции для SSIM-A2-01

Бренды по названию

Популярные бренды