Cabletron Systems SSIM-A2-01 Скачать руководство пользователя страница 64

Страница: 64 / 88

SmartStack SSIM-A2-01/SSIM-A8-01

Statistics

Server VCC Table

The Server VCC Table screen displays LANE server VCC information for a VAP.

Configure Direct

The VPI and VCI values for the VCC to the LECS. If an SVC is used, the SVC is
closed after the configuration phase. If the VCCs are not in use, the values will be
0/0.

Control Direct

The VPI and VCI values for the Control Direct VCC to the LES. The Control Direct
VCC is used for control frames to the LES.

Control Distribute

The VPI and VCI values for the Control Distribute VCC to the LES. The Control
Distribute VCC is used for control frames from the LES.

Multicast Send

The VPI and VCI values for the MS-VCC to the LANE BUS. The MS-VCC is used
by the VAP to transmit ATM broadcast frames (to the BUS).

Multicast Forward

The VPI and VCI values for the MF-VCC from the BUS. The MF-VCC is used by
the BUS to distribute ATM broadcast frames (to LANE clients).

Содержание SSIM-A2-01

























































































Результаты поиска

Содержание SSIM-A2-01

Отзывы:

Похожие инструкции для SSIM-A2-01

Бренды по названию

Популярные бренды

Cabletron Systems SSIM-A2-01, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SSIM-A2-01

Отзывы:

Похожие инструкции для SSIM-A2-01

Бренды по названию

Популярные бренды