Cabletron Systems SSIM-A2-01 Скачать руководство пользователя страница 60

Страница: 60 / 88

SmartStack SSIM-A2-01/SSIM-A8-01

Statistics

STE Frames

The number of spanning-tree explorer frames transmitted or received on the ATM
network on this VAP.

ARE Frames

The number of all-routes explorer frames transmitted or received on the ATM
network on this VAP.

Type

Rx Unicast

The number of frames received on this VAP with a non-broadcast destination
address.

Rx Broadcast

The number of frames received on this VAP with a broadcast destination address.

Rx Multicast

The number of frames received on this VAP with a multicast destination address.

Rx Forwarded

The number of frames forwarded on this VAP from ATM to other switch ports.

Transmitted

The number of frames transmitted to the ATM network.

Содержание SSIM-A2-01

























































































Результаты поиска

Содержание SSIM-A2-01

Отзывы:

Похожие инструкции для SSIM-A2-01

Бренды по названию

Популярные бренды

Cabletron Systems SSIM-A2-01, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SSIM-A2-01

Отзывы:

Похожие инструкции для SSIM-A2-01

Бренды по названию

Популярные бренды