Cabletron Systems SSIM-A2-01 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 88

background image

5

SmartStack SSIM-A2-01/SSIM-A8-01

Installation

One VAP per Uplink per VLAN

The SSIM-Ax-01 module does not allow configurations in which the following
frame operations take place within a single uplink module:

•

Bridging from ATM back to ATM.

•

Broadcasting a frame from Token Ring to more than one ATM ELAN.

These operations would occur if the uplink module provided more than one VAP
per VLAN. Therefore, the configuration shown in Figure 2 is not supported.

Figure 2. Unsupported Configuration

If you want to connect the same STS16-20RM Token Ring Switch to ATM via
more than one VAP, the VAPs must reside on different ATM uplink modules, as
shown in Figure 3.

Figure 3. Connecting One Switch to Two VAPs

«
...
12
13
14
15
16
...
»

Содержание SSIM-A2-01

























































































Отзывы:

Нет отзывов

Похожие инструкции для SSIM-A2-01

Бренд: D-Link Страницы: 267

Бренд: Abocom Страницы: 11

Бренд: Abocom Страницы: 19

Бренд: bintec elmeg Страницы: 33

APS6-400 Series

Бренд: Eaton Страницы: 114

Бренд: ZyXEL Communications Страницы: 116

Бренд: NETGEAR Страницы: 2

Бренд: Perle Страницы: 2

Бренд: Aaeon Страницы: 72

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: MA lighting Страницы: 49

Бренд: ADTRAN Страницы: 4

Developer's Board

Бренд: Sony Ericsson Страницы: 28

Бренд: Harman Страницы: 24

Бренд: ADTRAN Страницы: 20

Бренд: ETAS Страницы: 36

Data Capture Board CLC-CAPT-PCASM

Бренд: National Semiconductor Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды