Buell 2009 XB Series, Руководство по обслуживанию

Страница: 392 / 712

4. Rotate engine up. See 3.4 ENGINE ROTATION FOR
SERVICE .
Rear Muffler Bracket
1. See Figure 4-51 . Slide rear muffler bracket (11) over oil
line.
2. Apply LOCTITE 271 (red) and install rear muffler bracket
fasteners (12) and tighten to 32-36 ft-lbs (43-49 Nm).
3. Install oil line and p-clamp to swingarm. Tighten p-clamp
fastener to 48-72 in-lbs (5.4-8 Nm) See
3.11 OIL
RESERVOIR AND OIL HOSE ROUTING and 3.12 OIL
LINE FITTINGS .
4. Fill swingarm/oil tank with 2.5 quarts (3.3 liters) oil. See
1.6 ENGINE OIL AND FILTER .
NOTE
For details on installing components on XB12 models with
interactive exhaust systems, see
6.17 INTERACTIVE
EXHAUST SYSTEM, Installation .
5. Install muffler.
Front Muffler Mount
1. See Figure 4-51 . Install front muffler mount bushings (9).
NOTE
Never re-use front muffler strap. Always replace front muffler
strap with a new strap when removed from system.
2. Install new strap on front muffler mount (7).
3. Install front muffler mount fastener (8) loosely. Do not
tighten.
4. Install muffler.
Muffler and Straps
NOTES
• Torca muffler clamps have eliminated the need for silicone
or graphite tape during assembly. To verify sealing integrity
of muffler clamps and prevent the possibility of leakage,
Buell recommends that muffler clamp assemblies be dis-
carded and replaced each time they are removed.
• Due to the location of the CKP it will be necessary to align
the Torca Clamp to verify proper clearance between the
chin fairing and the CKP and Torca clamp.
1. Install muffler and new Torca clamp onto header.
NOTES
• If necessary, use a fiber hammer to fit muffler on header.
• For details on installing components on XB12 models with
interactive exhaust systems, see
6.17 INTERACTIVE
EXHAUST SYSTEM, Installation .
2. Install interactive exhaust cable to muffler.
NOTE
Never re-use front muffler strap. Always replace front muffler
strap with a new strap when removed from system.
3. See Figure 4-51 . Loosely install new front and rear muffler
straps (2, 5).
NOTES
• It is important that the front muffler mount is tightened last
in order to verify proper alignment of the exhaust system.
• When rear muffler straps have been installed, it is
important that strap fasteners do not contact idler pulley
bracket.
• On the front muffler mount fastener, torque is applied to
the head and not to the nut.
4. Tighten front strap fastener and alternately tighten rear
muffler strap fasteners evenly in the following sequence:
a. Front strap fastener: Tighten around the muffler until
snug.
b. Rear strap fastener: 48-60 in-lbs (5.4-7 Nm).
c. Once the fasteners on the rear muffler straps have
been tightened to torque, you need to alternately
tighten the fasteners to torque two more times to
make sure the straps are evenly tightened.
d. Front muffler mount fastener: 16-18 ft-lbs (21.7-24.4
Nm).
e. Front strap fastener: 108-120 in-lbs (12-14 Nm). Back
off fastener two full turns and then retighten to 108-
120 in-lbs (12-14 Nm).
5. See Figure 4-52 . Tighten the Torca clamp (1) to 45-50 ft-
lbs (61-68 Nm).
6. Install idler pulley. See 5.7 DRIVE BELT AND IDLER
PULLEY .
7. Install front sprocket cover. See 2.36 SPROCKET COVER .
8. Install chin fairing. See 2.50 CHIN FAIRING .
9. Adjust interactive exhaust cable. See 1.16 INTERACTIVE
EXHAUST CABLE .
HOME
4-40 2009 XB Service: Fuel System