Big Backyard HILLCREST F23270 страница 94 Скачать руководство пользователя

Страница: 94 / 112

[email protected]

2 x

Ground Stake 1-1/4 x 1-1/2 x 14”

Hardware

Wood Parts

4 x

#8 x 2-1/2” Wood Screw

WARNING:

To prevent tipping and avoid potential injury,

stakes must be driven 10-1/2” into ground. Digging or driving

stakes can be dangerous if you do not check first for under-

ground wiring, cables or gas lines.

Drive 1 (0318) Ground Stake 10-1/2” into the ground at (2352) A Frame Access R and (2356) A Frame Post on

the outside of the assembly and attach with 2 (S3) #8 x 2-1/2” Wood Screws per ground stake. (fig. 41.1 and 41.2)

0318

10-1/2” Into Ground

0318

Step 41: Attach A Frame Ground Stakes

2352

2356

Fig. 41.1

Fig. 41.2

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды