Big Backyard HILLCREST F23270 страница 32 Скачать руководство пользователя

Страница: 32 / 112

[email protected]

Step 9: Cafe Wall Assembly

Note: Pre-drill all holes using a 1/8” drill bit before installing the Lag Screws.
A:

On the ground lay flat 2 (2383) Posts then loosely attach (0348) SL Ground with 4 (H2) 1/4 x 2” Hex Bolts

(with lock washer, flat washer and t-nut); (2371) Floor End (in the top holes) and (2387) Side Arch (in the top

holes) with 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut) per board, as shown in fig. 9.1.

Keep bolts loose.

Make sure assembly is square and then fasten (2371) Floor End to (2383) Posts with 2 (LS1) 1/4 x 1-1/2” Lag

Screws (with flat washer) and (2387) Side Arch to posts with 2 (S2) #8 x 1-1/2” Wood Screws. (fig. 9.1)

Tighten all bolts.

Notice the hole

locations

Wood Parts

Hardware

8 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 1-1/2” Lag Screw (1/4” flat washer)

2 x

#8 x 1-1/2” Wood Screw

1 x

Side Arch 1 x 5 x 38-1/4”

2 x

Post 2 x 4 x 88”

1 x

Floor End 1 x 5 x 38-7/8”

1 x

SL Ground 1 x 5 x 38-1/4”

2387

0348

2371

2383

LS1

2387

Fig. 9.1

0348

1/4” lock

washer

1/4” flat

washer

1/4” t-nut

1/4” flat

washer

LS1

2383

2371

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды