Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 69 / 112

[email protected]

1 x

1/4 x 2-3/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 2-1/2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

#12 x 2” Pan Screw

Hardware

Wood Parts

Fig. 29.3

2355

1 x

MK Mount 2 x 3 x 41-1/2”

1 x

A Frame Lower Side B 5/4 x 4 x 48-5/16”

2381

Step 29: A Frame MK Wall Assembly

Part 2

Install 1 5/16” T-Nut into (2381) MK Mount. (fig. 29.2)

Loosely attach (2381) MK Mount to (2353) A Frame Floor Support with 1 (H11) 1/4 x 2-3/4” Hex Bolt (with

lock washer, flat washer and t-nut) and to (2359) A Frame Top Side with 1 (H2) 1/4 x 2” Hex Bolt (with lock

washer, flat washer and t-nut), as shown in fig. 29.3. Notice the direction the 5/16” T-Nut installed in Step C is

facing.

Loosely attach (2355) A Frame Lower Side B to (2356) A Frame Post and (2352) A Frame Access R with 2

(H3) 1/4 x 2-1/2” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 29.3)

Make sure the assembly is square then attach (2355) A Frame Lower Side B to (2356) A Frame Post and

(2352) A Frame Access R with 2 (S7) #12 x 2” Pan Screws. (fig. 29.3)

Tighen all bolts.

Notice t-nut location.

2352

1/4” Flat

Washer

1/4” Lock

Washer

1/4”

T-Nut

H11

2356

2353

Notice board location.

2359

1/4” Flat

Washer

1/4” Lock

Washer

1/4”

T-Nut

H11

2355

2381

Fig. 29.2

5/16”

T-Nut

2381

1 x 5/16” t-nut

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды