Big Backyard HILLCREST F23270 Скачать руководство пользователя страница 86

Страница: 86 / 112

[email protected]

Centre (2404) Tunnel Top Cross in the notch of (2403) Tunnel Top and attach with 1 (S2) #8 x 1-1/2” Wood

Screw. (fig. 39.4)

With a helper place 2 Tunnel panels together, make sure they are centred on (2403) Tunnel Top, leaving

a 1” overhang on each end. Attach Tunnel assembly with 4 (S10) #8 x 1” Pan Screws in each side of (2404)

Tunnel Top Cross and 8 (S10) #8 x 1” Pan Screws in (2403) Tunnel Top. (fig. 39.5, 39.6 and 39.7)

Turn assembly over and place (2392) Tunnel Arch centred on top of (2403) Tunnel Top then attach with 2

(S3) #8 x 2-1/2” Wood Screws. (fig. 39.7)

Step 39: Tunnel Assembly

Part 2

Hardware

2 x

#8 x 2-1/2” Wood Screw

16 x

#8 x 1” Pan Screw

1 x

#8 x 1-1/2” Wood Screw

Wood Parts

1 x

Tunnel Top Cross 5/4 x 3 x 16-1/2”

1 x

Tunnel Top 2 x 4 x 31-19/32”

1 x

Tunnel Arch 5/4 x 4 x 23-1/2”

2404

1”

Fig. 39.4

Fig. 39.7

Fig. 39.5

2404

2403

2392

2403

S10

x16

Notice holes in end

panel not used here

2403

S10

2392

2403

Fig. 39.6

2404

S10

(hidden)

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Бренды по названию

Популярные бренды