Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 44 / 112

[email protected]

Step 18: Attach Access Ladder to Fort

Pre-drill all holes using a 3/16” drill bit before installing the Lag Screws

Place the Access Ladder in the opening of the Access Wall, flush to the outside edge of (2371) Floor End

on the Swing Wall. Attach (2410) Right Access to (2371) Floor End with 1 (H12) 1/4 x 3” Hex Bolt (with lock

washer and flat washer and previously installed t-nut). (fig. 18.1 and 18.2)

Attach (2374) Left Access to (2371) Floor End with 1 (LS4) 1/4 x 4” Lag Screw (with flat washer). (fig. 18.1

and 18.2)

Attach (2395) SW Ground to (2374) Left Access with 2 (S2) #8 x 1-1/2” Wood Screws. (fig. 18.1 and 18.3)

Hardware

1 x

1/4 x 4” Lag Screw (1/4”flat washer)

1 x

1/4 x 3” Hex Bolt (1/4” lock washer, 1/4”flat washer, t-nut previously installed)

2 x

#8 x 1-1/2” Wood Screw

LS4

Swing Wall

Fig. 18.2

Fig. 18.3

2374

2371

1/4” lock

washer

2374

Fig. 18.1

1/4” t-nut

(previously

installed)

1/4” flat

washer

H12

2371

2395

LS4

H12

Access Wall

1/4” flat

washer

2410

2395

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды