manualshive.com logo in svg

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Поделиться
Скачать
Big Backyard HILLCREST F23270 Скачать руководство пользователя страница 96

 

96 

 

    

[email protected]

Step 43:  Monkey Ladder Assembly

C: 

 Attach (858) 1-1/8 x 18-5/8” Dowel to both posts with 2 (S2) #8 x 1-1/2” Wood Screws.  Two screws are 

installed from top of the rails and the others from the bottom as shown in fig. 43.3.

                                                                                                                                                                                                                                  

D: 

 At bottom of (2382) MK Posts attach (0353) MK Ground with 2 (H12) 1/4 x 3” Hex Bolts (with lock washer, 

flat washer and t-nut).  

Be sure to keep the bolts loose.

  (fig. 43.3)

E: 

 Make sure the assembly is square and then attach 1 (0369) Lower Diagonal to each end of (0353) MK 

Ground with 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, flat washer and t-nut), keeping the bolts loose, and to 

each (2382) MK Post with 1 (LS2) 1/4 x 2-1/2” Lag Screw (with flat washer).  Once lag screws are installed 

tighten all bolts from Steps D & E.  (fig. 43.3)

Note: Pre-drill all holes using a 1/8” drill bit before installing the Lag Screws and Wood Screws.
A:

  Insert 2 (858) 1-1/8 x 18-5/8” Dowels into 2 (2382) MK Posts as shown in fig. 43.1. 

B:

  Make sure shoulder of dowel is against each post before pre-drilling 

pilot holes.  Drill 1/8” pilot holes through the posts and into the dowel to 

prevent splitting. (fig. 43.2 and 43.3)

Wood Parts

Hardware

2 x 

1/4 x 3” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x  

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x 

1/4 x 2-1/2” Lag Screw (1/4” flat washer)

4 x 

#8 x 1-1/2” Wood Screw

2 x 

Lower Diagonal 2 x 3 x 37”

1 x 

MK Ground 1 x 4 x 55-1/4”

2 x 

MK Post 2 x 3 x 77-1/2” 

2 x 

Tennon Dowel 1-1/8 x 18-5/8” 

0369

S2

0353

2382

858

LS2

H2

H12

0369

2382

0353

LS2

2382

858

H2

LS2

858

2382

Fig. 43.1

Fig. 43.3

1/4” Flat 

Washer

1/4” Lock 

Washer

1/4” 

T-Nut

1/4” Flat 

Washer

Fig. 43.2

858

H12

0369

S2

x 2 per 

dowel

H2

Note: Pilot holes at 

bottom of this rail

Note: Pilot holes at 

top of this rail

Содержание HILLCREST F23270

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды