Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 53 / 112

[email protected]

Hardware

Wood Parts

12 x

#8 x 7/8” Truss Screw

6 x

#8 x 1-1/2” Wood Screw

1 x

Trim Short 1 x 2-1/2 x 19-5/8”

1 x

Short Trim 1 x 2 x 19-5/8”

6 x

CE Siding 3/8 x 3-1/2 x 36”

Step 24: Lower Access Wall Assembly

Part 1

2383

Access Wall

Fig. 24.1

Fig. 24.2

2383

0348

x 2 per board

1870

1808

1852

Flush to the outside edge of (2383) Post and tight to the top of (0348) SL Ground attach (1808) Short Trim to

(2383) Post with 3 (S2) #8 x 1-1/2” Wood Screws. (fig. 24.1 and 24.2)

Tight to top of (0348) SL Ground and tight to (1808) Short Trim attach 6 (1852) CE Siding to both (2383) Posts

with 2 (S0) #8 x 7/8” Truss Screws per board. Make sure there are no gaps between boards. (fig. 24.1 and 24.2)

Tight to (1852) CE Siding and top of (0348) SL Ground attach 1 (1870) Trim Short to (2383) Post with 3 (S2)

#8 x 1-1/2” Wood Screws. (fig 24.2)

2383

1808

1870

Flush

Tight

1852

x 6

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды