Big Backyard HILLCREST F23270 Скачать руководство пользователя страница 54

Страница: 54 / 112

[email protected]

Place (1868) Table Support flush to the angled edge of (0376)

Table Top, as shown in fig. 24.3. The overhang should measure

3-3/8” on each side. Attach using 5 (S7) #12 x 2” Pan Screws.

Place Table Top Assembly tight to the top of (1852) CE Siding,

(1808) Short Trim and (1870) Trim Short. Make sure (1868) Table

Support is flush to the outside edges of both (2383) Posts then attach

(1868) Table Support to each post with 2 (S3) #8 x 2-1/2” Wood

Screws per post. (fig. 24.4 and 24.5)

Hardware

Wood Parts

4 x

#8 x 2-1/2” Wood Screw

5 x

#12 x 2” Pan Screw

1 x

Table Top 5/4 x 6 x 32”

1 x

Table Support 2 x 2 x 38-3/4”

0376

1868

2383

Fig. 24.3

Flush

1868

0376

Fig. 24.5

1868

1852

1808

1870

Front Wall

Fig. 24.4

Step 24: Lower Access Wall Assembly

Part 2

Flush

3-3/8”

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Бренды по названию

Популярные бренды