Big Backyard HILLCREST F23270 страница 83 Скачать руководство пользователя

Страница: 83 / 112

[email protected]

Place (2362) Back Tunnel Support tight to bottom of (2423) A Frame Floor D, tight to inside edge of (2361)

A Frame Upright on the A Frame and (2379) Mid Joist on the main fort. (fig. 38.5, 38.6, 38.7 and 38.8) Attach

(2362) Back Tunnel Support to (2361) A Frame Upright from inside the fort with 2 (S4) #8 x 3” Wood Screws.

(fig 38.9)

Make sure top of (2362) Back Tunnel Support remains tight to bottom of (2423) A Frame Floor D and tight

to (2379) Mid Joist then attach to (2350) Front Floor from inside the fort with 2 (S7) #12 x 2” Pan Screws. (fig.

38.9)

Step 38: Connect A Frame to Fort

Part 2

Hardware

2 x #8 x 3” Wood Screw
2 x #12 x 2” Pan Screw

Wood Parts

1 x

Back Tunnel Support 2 x 3 x 36-39/64”

2362

Fig. 38.5

2361

Tight

Main Fort

Fig. 38.6

Fig. 38.7

Fig. 38.8

Fig. 38.9

A Frame

2373

2362

A Frame

2350

Flush

2362

2423

2362

2379

2353

View from

Underneath

Outside View

Inside View

2361

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды