Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 72 / 112

[email protected]

2356

Step 31: A Frame Floor Assembly

Have a helper hold up the A Frame MK Wall and A Frame Access Wall then measure 3/4” in from the edge

of (2353) A Frame Floor Support on the Rock Wall side and tight to the posts attach 1 (2368) A Frame Floor to

(2353) A Frame Floor Supports with 4 (S2) #8 x 1-1/2” Wood Screws. (fig. 30.1 and 30.2)

Measure 1” in from the edge of (2353) A Frame Floor Support on the Access Ladder Wall side and tight

to the posts attach 1 (2368) A Frame Floor to (2353) A Frame Floor Supports with 4 (S2) #8 x 1-1/2” Wood

Screws. (fig. 30.1 and 30.3)

Wood Parts

2 x

A Frame Floor 1 x 6 x 20-11/16”

2368

Hardware

8 x

#8 x 1-1/2” Wood Screw

Fig. 31.1

Fig. 31.3

Tight

2351

2368

2353

1”

2353

2351

2352

2356

2368

Access

Ladder

Wall

Rock Wall

Fig. 31.2

Tight

2368

2353

3/4”

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды