Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 109 / 112

109

[email protected]

STEP # STEP NAME

---------------------------

read by a supervising adult.

on your set that is easily seen and

Attach with screws provided to a location

---------------------------

ATTACH THIS WARNING & I.D.

PLAQUE TO A PROMINENT

LOCATION ON YOUR PLAY

EQUIPMENT! (Fort or Swing Post)

This provides warnings concerning

safety and important contact

information. A Tracking Number

is provided to allow you to get critical

information or order replacement parts

for this specific model

Final Step: Attach I.D. Plaque

------------------------

-----------------------

WARNING

--------------------

FORT OR

SWING POST

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды