Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 38 / 112

[email protected]

Step 14: Roof Frame Assembly

Part 1

Place 1 (2384) Post Support tight to top of (1502) Wall Support on Access Wall side at each (2383) Post and

1 (2384) Post Support tight to top of (2837) Side Arch on Cafe Wall side at each (2383) Post. Each (2384) Post

Support must be flush to the inside edge of each post. Attach each (2384) Post Support to posts with 3 (S2) #8 x

1-1/2” Wood Screws per board. (fig. 14.1 and 14.2)

Tight to the top and flush to the inside edge of each (2383) Post attach 1 (2364) Block to each (2384) Post

Support with 4 (S2) #8 x 1-1/2” Wood Screws per board. Notice the hole orientation on each board. (fig. 14.1

and 14.2)

Wood Parts

Hardware

28 x

#8 x 1-1/2” Wood Screw

4 x

Block 2 x 4 x 13”

4 x

Post Support 1 x 4 x 13-3/8”

2364

2383

2364

1502

2383

2837

Access Wall

2384

Flush

1502

Flush and

Tight

Notice hole orientation.

x 7 per

board

2384

Fig. 14.1

Fig. 14.2

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды