Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 102 / 112

102

[email protected]

Step 47: Slide Support Assembly

Part 2

Fig. 47.2

Fig. 47.3

At the end of (2372) Front Ground dig

one, flat bottom, 8” wide by 6” deep hole as

shown in fig. 47.3. Place (2388) SL Upright

in the hole, making sure that it is plumb.

(fig. 47.3)

Place (2140) Short Upright beside

(2388) SL Upright on the opposite side of

(2372) Front Ground making sure that it

is plumb. Notice the angled edge slopes

away from (2372) Front Ground. (fig. 47.2

and 47.3)

Loosely attach (2140) Short Upright and

(2388) SL Upright to (2372) Front Ground

with 1 (H12) 1/4 x 3” Hex Bolt (with lock

washer, flat washer and t-nut) per board.

(fig. 47.3)

Refill hole halfway with soil and

compact making sure (2388) SL Upright

stays plumb. Finish filling and compacting.

(fig. 47.3)

Tighten bolts in (2140) Short Upright

and (2388) SL Upright then attach (2372)

Front Ground to uprights with 1 (S15) #8 x

1-3/4” Wood Screw per board. (fig. 47.3)

WARNING:

Digging can be

dangerous if you do not check first for

underground wiring, cables or gas lines.

2388

6”

2140

2372

Angled edges

slope towards

Front Ground

H12

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

1 x

Short Upright 2 x 3 x 33”

Hardware

Wood Parts

2 x

#8 x 1-3/4” Wood Screw

2 x

1/4 x 3” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

H12

2140

S15

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды