Big Backyard HILLCREST F23270 страница 24 Скачать руководство пользователя

Страница: 24 / 112

[email protected]

Step 3: Swing Beam Assembly

Make sure triangle is

tight against beam

WARNING:

For your child’s

safety, orientate the swing hangers

as shown to ensure your swing will

have proper swing motion when

installed. Failure to do so could

result in premature failure of the

swing hanger or swing chain.

In the middle holes of (1825)

Back Beam install 2 Bolt-Thru Swing

Hangers (fig. 3.1) making sure the

swing hangers are oriented in the

direction shown in fig. 3.4 to maintain

proper swing motion.

In the end holes of (1826) Front Beam install 2

Bolt-Thru Swing Hangers (fig. 3.1) making sure the

swing hangers are oriented in the direction shown in

fig. 3.4 to maintain proper swing motion.

4 x

1/4 x 5-1/2” Hex Bolt

(1/4” flat washer, 1/4” lock washer, 1/4” t-nut)

4 x

5/16 x 1-1/2” Hex Bolt

(5/16” flat washer, 5/16” lock washer, 5/16” t-nut)

1 x Bolt-Thru Swing Hanger (pkg of 4)
1 x Triangle Plate (pkg of 4)

1 x

Front Beam 2 x 6 x 83-5/8”

1 x

Back Beam 2 x 6 x 83-5/8”

1826

1825

Fig. 3.4

Bolt-Thru Swing Hangers

Wood Parts

Hardware

Other Parts

Fig. 3.1

Attach 1 Triangle Plate to the

ends of each (1826) Front Beam

and (1825) Back Beam using

1 (G1) 5/16 x 1-1/2” Hex Bolt

(with lock washer, flat washer

and t-nut) per triangle plate in

the hole indicated in fig. 3.2 and

3.3.

Correct hole usage is very

important.

Triangle

Plates

Important!

Swing End

(With Overhang)

1826

Important!

Fort End Side

(No Overhang)

Fig. 3.2

Fig. 3.3

Attach 1 (H7) 1/4 x 5-1/2” Hex

Bolt (with lock washer, flat washer

and t-nut) to the ends of each (1826)

Front Beam and (1825) Back Beam.

The bolts do not attach to anything,

but

MUST

be installed to the beams

to prevent splitting and checking of

wood. (fig. 3.2 and 3.3)

Swing End

(With Overhang)

Fort End Side

(No Overhang)

1825

1/4” Flat

Washer

1/4” Lock

Washer

1/4” T-Nut

5/16” Flat

Washer

5/16” Lock

Washer

5/16” T-Nut

1826

1825

Bolt-Thru Swing Hangers

Make sure holes are aligned.

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды