Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 87 / 112

[email protected]

With helper place Tunnel Assembly over floor boards. Make sure (2403) Tunnel Top is centred over the

pilot holes in (2398) Tunnel Left End and the bottoms of both boards are flush to each other. Ends of the

Tunnel Assembly should sit tight against both (2361) A Frame Uprights. Attach (2398) Tunnel Left End to

(2403) Tunnel Top with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 40.1 and 40.2)

Make sure the bottom of the Tunnel sits 1-1/2” up from the bottom of both (2362) Back Tunnel Support and

(2373) Front Tunnel Support then install 1 (S10) #8 x 1” Pan Screw to each support in the holes closes to the A

Frame. (fig. 40.3)

Maintaining the 1-1/2” measurement on each (2362) Back Tunnel Support and (2373) Front Tunnel Support

install 6 (S10) #8 x 1” Pan Screws in each support working from A Frame towards the main fort. (fig. 40.3)

Step 40: Attach Tunnel Assembly to Fort

Part 1

Hardware

Fig. 40.1

2403

x 6 per

side

Fig. 40.2

Fig. 40.3

2398

2 x

#8 x 2-1/2” Wood Screw

12 x

#8 x 1” Pan Screw

S10

Flush

S10

1-1/2”

Main Fort

2362

A Frame

2373

and

2361

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды