Big Backyard HILLCREST F23270 Скачать руководство пользователя страница 42

Страница: 42 / 112

[email protected]

Step 16: Attach Gable to Roof

Hardware

16 x

#8 x 1-1/2” Wood Screw

Along each (2394) Roof Support measure 8” up from the top of (2420) Bottom Gables then tight to the

underside of the Roof, on each Roof Support Assembly, attach 2 (2419) Gable Sides, at the measured spot, to

(2394) Roof Supports and (2420) Bottom Gable with 2 (S2) #8 x 1-1/2” Wood Screws per board. (fig. 16.1)

Tight to the underside of the Roof, at the peak of each Roof Support Assembly, attach 1 (2418) Gable Top to

the (2394) Roof Supports with 4 (S2) #8 x 1-1/2” Wood Screws per board. (fig. 16.1)

Repeat for opposite side.

Wood Parts

2 x

Gable Top 1 x 6 x 19”

4 x

Gable Side 1 x 4 x 13-23/32”

2418

Fig. 16.1

Inside View

2420

2418

2394

x 16

2419

8”

2419

Notice board orientation.

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Бренды по названию

Популярные бренды