Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 90 / 112

[email protected]

2 x

#8 x 1-3/4” Wood Screw

2 x

#8 x 2-1/2” Wood Screw

Hardware

S15

Place (2401) Tunnel Right End tight to top of the Tunnel Assembly and centred pilot holes over (2403)

Tunnel Top. Make sure the distance between top of (2350) Front Floor and bottom of (2401) Tunnel Right End

measures 22”. Notice the bolt hole location. (fig. 40.8, 40.9 and 40.10)

Attach (2401) Tunnel Right End to (2403) Tunnel Top with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 40.10)

Make sure (2401) Tunnel Right End is flush to the bevelled edge of (2396) Tunnel Corner Support and

attach with 2 (S15) #8 x 1-3/4” Wood Screws. (fig. 40.9 and 40.10)

Step 40: Attach Tunnel Assembly to Fort

Part 4

S15

Notice bolt hole

location

Notice bolt hole on this

side and at bottom.

Fig. 40.8

2401

Fig. 40.9

Fig. 40.10

S15

2403

2396

Tight

2401

2396

2350

Wood Parts

1 x

Tunnel Right End 5/4 x 4 x 23-7/16”

2401

22”

Flush

Note: (2401) Tunnel Right

End must be flush to the

outside edge of (2396)

Tunnel Corner Support.

DO NOT OVER HANG.

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды