Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 39 / 112

[email protected]

Wood Parts

Hardware

4 x

#8 x 1-1/2” Wood Screw

8 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

4 x

1/4 x 4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

Top Front Back 1 x 5 x 46-5/8”

2 x

SL Ground 1 x 5 x 38-1/4”

2391

0348

Step 14: Roof Frame Assembly

Part 2

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

On the Cafe Wall and Access Wall sides place 1 (0348) SL Ground tight to top of each (2384) Post Support

and flush to the outside edges of each (2364) Block. Attach to each (2364) Block with 4 (H2) 1/4 x 2” Hex Bolts

(with lock washer, flat washer and t-nut) per board. (fig. 14.3 and 14.4)

On the Front Wall and Swing Wall sides place 1 (2391) Top Front Back flush to the top and outside edge of

each (2364) Block. Attach to each (2364) Block with 2 (H4) 1/4 x 4” Hex Bolts (with lock washer, flat washer and

t-nut) in the top holes and 2 (S2) #8 x 1-1/2” Wood Screws in the bottom holes, per board. (fig. 14.3 and 14.4)

0348

Swing Wall

Cafe Wall

Access Wall

2391

2364

x 8

x 4

0348

1/4” lock

washer

1/4” flat

washer

2384

Fig. 14.3

Fig. 14.4

Front Wall

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды