Big Backyard HILLCREST F23270 Скачать руководство пользователя

Страница: 70 / 112

[email protected]

Hardware

Wood Parts

Step 30: A Frame Access Wall Assembly

Part 1

Loosely attach 2 (2361) A Frame Uprights to 1 (2353) A Frame Floor Support with 2 (H11) 1/4 x 2-3/4” Hex

Bolts (with lock washer, flat washer and t-nut) and to 1 (2359) A Frame Top Side with 2 (H2) 1/4 x 2” Hex Bolts

(with lock washer, flat washer and t-nut), as shown in fig. 30.1.

Loosely attach (2351) A Frame Access L and 1 (2356) A Frame Post to (2353) A Frame Floor Support with

1 (H11) 1/4 x 2-3/4” Hex Bolt (with lock washer, flat washer and t-nut) per board and to each (2361) A Frame

Upright with 1 (G21) 5/16 x 3-3/4” Hex Bolt (with lock washer, flat washer and t-nut) per board. (fig. 30.1)

Fig. 30.1

2359

4 x

1/4 x 2-3/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

5/16 x 3-3/4” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

2 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

A Frame Top Side 1 x 4 x 49-3/4”

2 x

A Frame Upright 2 x 3 x 41-1/2”

1 x

A Frame Access L 2 x 4 x 66-3/16”

1 x

A Frame Floor Support 2 x 4 x 36-31/32”

1 x

A Frame Post 2 x 4 x 66-3/16”

H11

G21

2359

Notice bolt hole towards bottom

G21

5/16” Flat

Washer

5/16” Lock

Washer

516”

T-Nut

1/4” Flat

Washer

1/4” Lock

Washer

1/4”

T-Nut

2353

2351

2361

2356

G21

H11

1/4” Flat

Washer

1/4” Lock

Washer

1/4”

T-Nut

2361

2353

2356

2351

Содержание HILLCREST F23270

















































































































Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды

Big Backyard HILLCREST F23270, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HILLCREST F23270

Отзывы:

Похожие инструкции для HILLCREST F23270

Бренды по названию

Популярные бренды