Atten ATM3500A Скачать руководство пользователя | Manualshive

Страница: 60 / 203

background image

Default

The default input resistance for all measurements is 10M Ω. Please
refer to

Table 2-1

on

page 24. The DC input resistance can only be

changed for measurements with 100mV, 1V or 10V range. For 100V
DCV,   1000   V   DCV   and   other   measurement   functions,   the   input
resistance is fixed at 10M Ω and can not be changed.  Also note that
the   user  selected  value   is   stored  in  a  volatile  memory.  The  default
setting will be restored after the meter has been turned off.

How to set the DC input resistance

You can set the DC input resistance either through the front panel
operation or through the remote interface operation.

Front Panel Operation

Press DCV , and then use

◁

and

▷

buttons to locate “INPUT

R” option. Press ENTER to select it. Then select desired value for the
input resistance by pressing

◁

or

▷

button. Press ENTER to choose it.

Two values are available: 10M Ω or > 10G Ω. The locations of these
buttons are shown with red rectangle frames in

Figure 4-4

.

Figure 4-4

Remote Interface Operation

The automatic input resistance mode can be enabled / disabled. With
AUTO OFF (default), the input resistance is fixed at 10MΩ for all
ranges. With AUTO ON, the input resistance is set to >10GΩ for the
three lowest DC voltage ranges (100mV, 1V and 10V). Use the

60

«
...
58
59
60
61
62
...
»

Содержание ATM3500A












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATM3500A

Бренд: Keithley Страницы: 2

Бренд: Fluke Страницы: 2

Бренд: Actron Страницы: 36

Бренд: Actisense Страницы: 16

Бренд: Actisense Страницы: 21

Бренд: Greenlee Страницы: 48

Бренд: Greenlee Страницы: 84

Бренд: Gossen MetraWatt Страницы: 20

Бренд: IDEAL INDUSTRIES Страницы: 9

Бренд: Mastech Страницы: 26

Бренд: UYIGAO Страницы: 26

Бренд: koban Страницы: 117

Бренд: Pro's Kit Страницы: 16

Бренд: Hanatech Страницы: 116

Бренд: UNISource Corporation Страницы: 21

Бренд: Omega Страницы: 14

Бренд: Keithley Страницы: 91

Бренд: KYORITSU Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды