Atten ATM3500A Скачать руководство пользователя страница 26

Страница: 26 / 203



ACI: Selects AC current measurement.



Ω4: Selects 4-wire resistance measurement.



PERIOD: Selects period measurement.



: Selects diode testing.



TCOUPL: Selects thermocouple temperature measurement.

2.3.

Second row without SHIFT button:



FILTER: Enable or disable the digital filter.



DIGITS: Changes resolution.



RATIO: Enables the dcv:dcv ratio function.



%: Calculates the ratio to a target value in percentage.



MIN/MAX: Captures the minimum or maximum readings from the

measurement.



NULL: Activates the offset function in order to get the real
measured reading.

2.4.

Second row with SHIFT button:



STEP: Scans from a channel to the next channel in delayed action

when using the scanner card.



SCAN: Enables scanning function when using the scanner card.



LIMITS: Used for Setting upper and lower limit values for readings.



MX+B: Used for calculating slope. X is the normal display reading.

M and B are constants defined by user for scale factor and offset.

Содержание ATM3500A












































































































































































































Результаты поиска

Содержание ATM3500A

Отзывы:

Похожие инструкции для ATM3500A

Бренды по названию

Популярные бренды

Atten ATM3500A, Руководство пользователя

Результаты поиска

Содержание ATM3500A

Отзывы:

Похожие инструкции для ATM3500A

Бренды по названию

Популярные бренды