Atten ATM3500A Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 203

background image

average to produce a reading for dislay.filter takes the specified
number of reading conversion, averages them and produces a reading.
It then flushes the stack and starts over with an new User can set the
number to anything from 1 to 100Consequentter yields one reading for
display every specified number measurement r
Digital filter is not available for diode, continuity, frequency and period
measurements.

Default

The digital filter is enabled and is in moving average mode with 10
readings by default.

How to enable/disable digital filter

Press FILTER button to switch the digital filter function.
The “FILT” anunnciator indicates the state of the digital filter. When it
is lit, the filter is enabled.

How to configure digital filter fo

You can configure the digital Filter either through the front panel
operation or through the remote interface operation.

Front Panel Operation

For READINGS setting, please press CONFIG and then FILTER button
for selecting READINGS. Press ENTER to access. Use

◁

,

▷

,

△

and

▽

buttons   to   set   the   READINGS   (from   2   to   100)   in   order   to   get   an
average value. Press ENTER when it’s ready.
For MODE setting,  please press CONFIG and then FILTER button for
selecting MODE. Press ENTER to access. Use

◁

,

▷

to select MOVING

AVG. or REPEAT AVG.. Please ENTER to confirm.
Press FILTER button to enable or disable this function.

Remote Interface Operation

Use the following commands to set your digital filter:

SENSe:AVERage:TCONtrol {MOVing|REPeat}
SENSe:AVERage:TCONtrol?
SENSe:AVERage:COUNt {<

value

>|MINimum|MAXimum}

SENSe:AVERage:COUNt? [MINimum|MAXimum]

56

«
...
54
55
56
57
58
...
»

Содержание ATM3500A












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATM3500A

Бренд: Meterman Страницы: 14

Бренд: Kusam-meco Страницы: 16

Бренд: ConLAB Страницы: 10

Бренд: Greenlee Страницы: 48

Бренд: Greenlee Страницы: 84

Бренд: Surtek Страницы: 52

Бренд: CEN-TECH Страницы: 4

Бренд: optofidelity Страницы: 51

Бренд: APPA Страницы: 24

SNR-MPX-2E1-SFP

Бренд: NAG Страницы: 16

Бренд: Elma Страницы: 44

Бренд: Amprobe Страницы: 55

Бренд: Steinberg Systems Страницы: 21

Бренд: Steinberg Systems Страницы: 23

Бренд: Conrad Страницы: 34

Бренд: YATO Страницы: 52

Бренд: Datron Страницы: 202

Бренд: Magnum Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды