Atten ATM3500A Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 203

background image

ACI, Frequency, Period and Resistance functions.

How to program each channel with measurement function

Press SHIFT + FILTER

for scanning configuration. Use

◁

and

▷

to scroll through submenus. Press ENTER on “SET SCAN CHA”

submenu. Use

◁

and

▷

to switch from channel 1 to channel 10, and

use

△

and

▽

to switch among the measurement functions. Leave an

unused channel with a blank space (----). Press ENTER when ten
channels are all defined.

How to configure scan count, scan interval and store
measurement readings

Press SHIFT + FILTER for scanning configuration. Use

◁

and

▷

buttons to scroll through submenus. Press ENTER to select

“OPERATION” submenu. Use

◁

and

▷

to switch among scan count

(COUNT), scan interval (TIMER) and store (STORE) options. Then press
ENTER on your selection. Use

◁

and

▷

to move through the digits and

△

and

▽

to increase or decrease the numbers to a desired value. For

STORE option, you can select ON to instruct the meter to store the
measurement results for later retrieving or select OFF. Press ENTER to
set the value.

How to open and close the channels

Press SHIFT + FILTER for scanning configuration. Use

◁

and

▷

buttons to scroll through submenus. Press ENTER on “----”

when you need to close a specific channel. Press ENTER again on
“CHANNEL”. Use

◁

and

▷

to move through the digits and

△

and

▽

to

increase or decrease the numbers to the desired channel number.
Press ENTER to close the channel.
To open all channels, simply press ENTER on “OPEN ALL” option. Press
SHIFT + FILTER to scan as shown as

Figure 4-32

.

109

«
...
107
108
109
110
111
...
»

Содержание ATM3500A












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATM3500A

Бренд: Keithley Страницы: 94

Бренд: Keithley Страницы: 168

Бренд: Raisecom Страницы: 19

Бренд: VICI Страницы: 8

Бренд: Metravi Страницы: 3

Бренд: Somogyi Страницы: 40

Бренд: Cisco Страницы: 42

Бренд: Cisco Страницы: 24

Бренд: Cisco Страницы: 244

Бренд: FLIR Страницы: 32

Бренд: Targus Страницы: 34

Бренд: APPA Страницы: 62

Бренд: APPA Страницы: 77

Бренд: IDEAL INDUSTRIES Страницы: 15

Бренд: MARTINDALE Страницы: 4

Бренд: ADInstruments Страницы: 45

Бренд: Viessmann Страницы: 16

Бренд: Daiichi Electronics Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды